How long does it take to remove a dishwasher

Ashley Iredale

Need to know

• Replacing an existing dishwasher is a relatively simple job if you're handy with a screwdriver
• If you're installing a dishwasher for the first time there are some rules to make sure your installation is safe and legal

A dishwasher is a great labour-saving device that not only saves you time cleaning up in the kitchen, but is also a very water- and energy-efficient way to do the dishes.

And the good news is, installing one is a pretty simple job – especially if you're replacing an old one that's given up the ghost. That said, as with installing any appliance, there are a few things you should keep in mind to make sure it all goes smoothly, especially for a new installation where there are several rules you need to follow.

On this page:

What you need to replace a dishwasher

Replacing an existing dishwasher is a relatively easy job (provided you've measured up correctly and your new dishwasher fits in the space under your bench). All the infrastructure you need – power, water, drainage and space – are already in place. It's largely a matter of taking the old one out, connecting the new one to the drain and inlet tap, then plugging it in, and your new appliance is good to go.

Dishwasher installation tools

You'll need the following:

• A screwdriver and/or a driver drill
• A dropsheet or cardboard (optional)
• Tape (optional)
• A mop and bucket to clean up any spills
• The inlet and outlet hoses that came with your dishwasher, and the mounting hardware that was included.

Read more: Can you wash it in the dishwasher?

Step-by-step guide to replacing a dishwasher

1. If it still works, consider turning the water off and running the old dishwasher for about 30 seconds to pump out any residual water in the bottom of it first.
2. Turn off the water and disconnect the power, water inlet and drain hoses under the kitchen sink.
3. Lay a drop sheet or some cardboard down to prevent marking your floors, and be prepared to mop up any spills from the now disconnected piping.
4. Remove any screws or bolts securing the dishwasher to your countertop or cabinetry and gently slide the unit out onto the drop sheet or cardboard. Pull the old unit out of the way to make space for the new one.
5. Look inside the cabinetry for damage, and clean the floor under the old dishwasher.
6. Unpack the new dishwasher and keep the cardboard to protect the floor as you wrangle it into place.
7. Check the new machine's manual for any specific instructions or tips for installation.
8. Adjust the feet on your dishwasher so that it sits in a stable and level way. You may need to adjust it again when it's in place, but getting it close now is easier than when it's under your counter.
9. Feed the power, water and drainage lines through the hole in your cabinetry and connect them up under the sink.
10. When connecting the waste water hose, make sure it's looped up and over in an arch – use the handy U-bend that's supplied with the dishwasher for this purpose. Leave the end of the hose as high as possible in the drain pipe – if you don't, you might create a syphon effect in your drainage, which could potentially damage your appliance – then clamp the hose down.
11. Move your new dishwasher into the space in your cabinetry. Feed cables and hoses through the cabinetry as you go to avoid crushing or kinking them as your dishwasher slides into place. (Alternatively, before sliding it into place, you can secure everything to the floor with tape, along the centreline of the dishwasher so it won't tangle in the dishwasher's feet).
12. Once the dishwasher's in place, readjust its feet to make sure it's level and stable – this shouldn't take much because you pre-adjusted them earlier.
13. Turn everything on and give it a test run to make sure it's all connected and working properly, keeping an eye out for any leaks.
14. Securely anchor your dishwasher to the cabinetry. Dishwashers are very stable and contained when closed, but if not properly secured, they can tip forward when you slide the drawer out to empty it. While every dishwasher's different, this is generally just a matter of driving a couple of screws in, so there's no reason to neglect it.

Tip for dish-drawer-style machines

If you're installing a dish-drawer-style dishwasher, such as those from Fisher & Paykel, then you may need to remove the drawer from the chassis before sliding it into place – this can make the installation a little tricky, as you'll need to feed the cable and hoses, which are connected to the drawer, through the chassis to their destinations. So you'll need the drawer to be close enough that they'll reach, but far enough away that you have room to install the chassis.

Looking for dishwashers?

We've tested to find you the best.

What to do before installing a new dishwasher for the first time

There are lots of rules you need to be aware of when installing a dishwasher for the first time. Because dishwashers use both water and electricity, the risk of a catastrophic outcome should something go wrong is much higher than for most other appliances – the rules exist to keep you, your home, and everyone else safe.

Dishwasher installation tools

As well as the tools needed for a replacement installation, you'll need a couple of other things:

• A drill, hole saw or other means of making a 100 x 150mm hole in the side of your cabinetry
• A crowbar or similar for removing cabinetry
• Sealant for protecting your benchtops from steam and water damage
• A brush or roller to apply the sealant
• A new tap connection
• A new drain connection with an attachment for the dishwasher drain hose
• A new power outlet and the right cabling.

Your plumber and electrician will probably be able to supply the last three items.

Getting started

Decide where the dishwasher is going to go – which will be one of the cabinet spaces on either side of your sink, as this is where you'll access water and drainage.

Separating power points and water pipes

Under the Building Code of Australia, power points and water pipes can't be installed in the same cabinet void as your dishwasher – instead, your drainage, power and water supplies must be installed in the next cabinet along, with hoses and cables passing through a small hole (about 100 x 150mm) to the appliance. Ever wondered why your dishwasher's plug is under the sink, not behind the appliance? It's to reduce the risk of electrocution if it springs a leak.

Getting in licensed tradespeople

And if your kitchen doesn't have the necessary fittings already, you'll need licensed tradespeople to install them for you – an electrician for the power point and a plumber for the drain and water supply.

This isn't just for peace of mind, it's because legally only licensed tradespeople can touch your home's wiring, sewer or water pipes. Do the work yourself and you could cop a nasty fine, and your insurance company could deny any future claims if there's a problem down the track.

Other important things to think about when installing a dishwasher

If you're retrofitting a dishwasher to an existing kitchen, you'll need to remove the cabinet unit where your dishwasher is going to go. You may be able to do this yourself, but it's probably worth hiring a professional, in case you damage other parts of your kitchen in the process.

Next, you need to consider your counters. Steam and water spillage from your dishwasher can damage laminated benchtops, so it's important to ensure the undersides of benches are sealed to minimise the risk of water damage. 

Finally, most dishwashers (particularly built-under models) are heavy, unwieldy appliances with lots of sharp edges, so practise safe handling procedures. Ideally, have a friend or family member help you when carrying it into the kitchen.

Text-only accessible version

• Measure your cabinetry to make sure your replacement dishwasher will fit before buying.
• Protect your floors with a drop sheet or cardboard.
• Disconnect your old dishwasher by turning off the water and power, unplugging the hoses and cables, and removing any screws securing the dishwasher to the cabinetry.
• Remove the old dishwasher, clean the floor and inspect the cabinetry for damage.
• Unbox the new dishwasher, check for scratches or dents, and position it close to the installation point.
• Adjust the feet to ensure the dishwasher is level and stable, and feed the cables and hoses through the hole in the back of your cabinetry.
• Connect the water, drain and power connections under your sink and start wrangling your dishwasher into place, taking care not to kink or damage the hoses as you go.
• Turn on the water and electricity, and give the dishwasher a test run, keeping an eye out for any leaks.
• Secure your dishwasher to the cabinetry so it won’t tip over, following the instructions in your manual.
• Dispose of your old dishwasher responsibly.

Read more: 7 ways to make your dishwasher last longer

We care about accuracy. See something that's not quite right in this article? Let us know or read more about fact-checking at CHOICE.

How long does it take to remove and install a dishwasher?

Can you easily pull out a dishwasher?

How hard is it to change out a dishwasher?

How long does it take to replace an existing dishwasher?