Factory Reset BLU View 2 – This article will give a set of instructions about performing hard/soft/remote reset on BLU View 2. Read this article and choose one method and reset your BLU View 2. Read More – Increase RAM size BLU View 2 after root? Show
BLU View 2 is one of the popular Device In series. But Sometimes this Device may give errors. Then we have to deal with them. In that situation, Hard and Soft Reset give us the best opportunity to settle the problem. There are few ways to factory reset BLU View 2
WARNING! How to Hard Reset BLU View 2
How Factory Reset BLU View 2If for some reason your BLU View 2 is unable to boot into Normal Android Mode, and you Still need to perform a factory reset, the instructions are a bit difficult, but they do the same thing. Note – We recommend you get full back up.
Read More – Increase Internal Rom BLU View 2 after root
Factory Reset BLU View 2 with Android Device Manager
Factory Fully Reset BLU View 2 – entire Device (advance)In the above three methods, we only do reset but in this, we are going to replace the entire android system. If you buy a BLU View 2 Device, then it has a Stock ROM. Stock ROM is the Original ROM and Official Rom that a Device has. So, installing Stock ROM does not avoid your warranty. We found dedicated posts about flashing Stock Roms on “Gogorapid”. Go to that site and Flash a new Rom to your Device. Frequently asked questions and answersHi, however, I reset my Device successfully but I forgot to get back up before reset. I want to know, Can I get my data now? WhatsApp messages, Viber? Yes, If you have lost data on your BLU View 2, do not worry, follow this guide and you will know how to perform Blu data recovery to recover your lost photos, videos, contacts, and more. but I can’t say that you can get all the data. try this. Remove Pattern Lock, Device passwordA lot of people suffering from this problem. they don’t know how to remove Pattern Lock from their Devices. If you use any third-party app to set Pattern Lock then Uninstall it first. If you do not use any app then you may have been set it through the Device setting. Try to find it and remove it. If you can’t find then your final solution is, “Factory reset” or Flashing Stock Firmware. After resetting, Autoboot or bootloop or auto restartFirst, Give it to 5minutes. Then press power +Volume Up + home together until the logo shows up, after that, select factory reset If it Auto boot or auto restart – it could be Power switch is defective and could be always depressed. Maybe your Device case is pressing on it. So, remove that case for a little. After that, try to go to Normal Mode. If is does not work, then install Stock Rom – Flashing Stock Firmware. After factory reset my Device can’t connect to the internetQ: I performed a reset on my BLU View 2 Device. Now I can’t connect to the internet and the sim card was not recognized. A: If there is no error msg, then Contact your Network severs provider (SIM) and you should ask for Internet settings for your Device. A: Reset your Blu again. If it is failed or goes wrong again, then try to flash Official Stock Rom. – Flashing Stock Firmware. Stuck at BLU View 2 Logo ScreenMost of the time, the phone or tablet may be stuck for a long time. Then, letting the phone rest for a few more minutes is a good solution. (10 minutes) Upgrading uses more RAM on the device. If your RAM is small, it may take some time. If the problem is persistent, it could damage your device system. So, try resetting your Blu. If it does not work, you need to install Stock ROM. – Flashing Stock Firmware. Fix – Device that says “NO COMMAND” in recovery modeWhen you see the “No Command” screen you have to do the following. Also, note that you should try different button combinations and find the right combination for your device.
Try different button combinations until you find the right one. When you have found the right button combination and the recovery menu appears, select “Wipe Cache Partition”. How do you reset a Blu View 2 without command?Restore with hard reset or Recovery mode BLU View 2. 1- First turn off your BLU View 2 completely. ... . 2- Keep holding on volume down and power keys together for a few seconds in your BLU View 2. ... . 3- When the BLU logo is displayed, release the buttons.. When I try to factory reset my phone it says no command?If you are in the no command bootloop on Android, your best solution is to either factory reset your device or flash a ROM on your device. This should fix the very core files of your device, and this should help get rid of no command errors.
How do you reset a Blu phone without command?Solution 2: Factory Reset Phone To Fix Android Recovery No Command. First, enter into the recovery mode.. Press the Volume Up/Down button to go to the Wipe data/factory reset option.. Press the Power button to select the Wipe data/factory reset option.. Why does my Blu phone say no command?Android “no command” error usually shows up when you try to access the recovery mode or while installing a new software update. In most cases, your phone is just waiting for a command to access recovery options.
|